furuno navnet vx2 c-map nt max manual

You can inscribe the mark from any mode except nav data, when playing back data or conducting any test. Note that this function requires position data. Up to six data boxes (two in case of large characters) may be shown, and the default data boxes are position (in latitude and longitude), course over ground, speed over ground and trip log. The user may choose which data to display, where to locate it, and show or hide it as desired. The default function key settings are as shown in the table below.It allows you to view and control a simulated plotter, radar and sounder picture, without position-fixing equipment, network radar or a network sounder. The message “Now getting demo data. If you require manual tuning, do the following: 1. Press the MENU key to display the main menu. 2. Press the RADAR DISPLAY SETUP soft key. 3. In addition to reducing clutter, the FTC can be used in fine weather to clarify the picture when navigating in confined waters. In addition, the range setting will also automatically adjust the range ring interval so that accurate range measurements may be made while operating on any range setting. The range, range ring interval and pulselength appear at the top left-hand corner of the display. SHORT or MEDIUM for 1.5 nm, 1.5 sm, 3 km and MEDIUM or LONG for 3 nm, 3 sm, 6 km. Targets are painted at their measured distances and in their directions relative to own ship’s heading. Check the range ring interval and judge the distance of the echo from the inner edge of the nearest ring. The selected VRM’s indication, at the bottom of the screen, is highlighted. The bearing to the target appears in the range and bearing box at the bottom right-hand corner on the screen. It is a line from the own ship position to the outer edge of the radar display area and appears at zero degrees on the bearing scale in head-up mode;. TTM targets can come from a NavNet connected radar, or from other ARP radar that is outputting the TTM message.

• furuno navnet vx2 c-map nt max manual, furuno navnet vx2 c-map nt max manual, furuno navinet vx2 c-map nt max manualx manual, furuno navinet vx2 c-map nt max manual download, furuno navinet vx2 c-map nt max manual pdf, furuno navinet vx2 c-map nt max manual 2017, furuno navnet vx2 c-map nt max manual.

How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used.Distance to Distance to. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Each NavNet product is assigned an IP address to enable transfer of images between other NavNet products. For example, video plotter pictures can be transferred to a radar and vice versa. Operating Controls Display unit controls The radar, video plotter, sounder and chart systems are operated with the controls of the display unit. Ten keys are labeled and they provide the function shown on their labels. The five soft keys provide various functions according to current operating mode. Their labels for their current functions are shown on the screen to the left of the keys.Insert the appropriate chart card for your area as follows: 1. During this period the equipment is inoperative. A set of soft keys for adjustment of brilliance and hue appear. Active soft key is highlighted. MANUAL SET follows the color settings on the CHART DETAILS menu for the plotter and the RADAR DISPLAY SETUP menu for the radar. In addition to the full-screen display, you can divide the screen into halves and thirds to show two and three sets of images on a combination display. The icons of modes not available are shaded. HOTPAGE 1-HOTPAGE 6 are user-arrangeable displays called “hot pages,” which you can configure as you like. For further details, see the paragraph “7.6 Hot Page Setup.”. This is not necessary when only one network radar or network sounder is connected. 1. Roll the Trackball to shift the cursor.

Below are examples of dot spacing and target movement. (a) Ship turning (b) Ship running. False target situations may be recognized, however, if you understand why they are displayed. If the angle subtended at the antenna is more than a few degrees, a non-detecting sector or blind spot may be produced. Within this sector, targets can not be detected. 2.27.2 SART (Search and Rescue Transponder) A Search and Rescue Transponder (SART) may be triggered by any X-Band (3 cm) radar within a range of approximately 8 nm. Own ship marker blinks faster. Other GPS receiver: The message “NO GPS FIX” appears and is accompanied by the aural alarm and alarm icon. For further details see paragraph 7.10. Compass display The compass display, shown in combination displays, provides steering information. The compass rose shows two triangles: the red triangle shows own ship’s course and the black triangle, which moves with ship’s course, shows the bearing to destination waypoint. The own ship marker moves according to direction and distance off course. It is useful for monitoring ship’s progress toward a waypoint. The own ship marker shows the relation between ship and intended course. The user may select what data to display and where to display it. For details see the paragraph “7.8 Nav Data Display Setup.” Appropriate sensors are required. Each press of the key changes the presentation mode and presentation mode indication (top right-hand corner of the screen) cyclically in the sequence of North-up, Course-up and Auto course-up. The screen shifts in the direction opposite of cursor location. 2. To turn off the cursor, press the CENTER soft key. This also returns the own ship marker to the screen center. These frames are called indices and they show you what parts of the chart can be enlarged in the current range. Simply place the cursor on the lighthouse or buoy mark. Port service icons Selected Navionics GOLD charts show services available at ports, with icons. 1.

Zoom is not available when the display is shifted. 2.16.1 Manual shift The sweep origin can be shifted in any presentation mode to a point specified by the cursor by up to 50%. It can also be used to measure the range and bearing between two targets. 2.17.1 Predicting collision course The procedure below may be used to check if a radar target is on a potential collision course with your vessel. This function is useful for alerting you past possible collision situations.Echoes received from stable targets such as ships appear on the screen at almost the same position during every rotation of the antenna. On the other hand, unstable echoes such as sea clutter appear at random positions. This function requires position and heading data. 1. Operate the Trackball to place the cursor on the target whose position you wish to output. When ships, islands, landmasses, etc.Note 2: If the network radar is set to standby while the guard alarm is active, the guard alarm is cancelled. PUSH ANY KEY TO CONTINUE.” appears. Press any key and then set a guard zone. 2.23.3 Setting watchman stand-by interval The watchman standby interval, that is, the number of minutes the radar is in standby, can be set to 5, 10 or 20 minutes as follows: 1. Once a target is acquired automatically or manually it is automatically tracked within 0.1 to 16 nm. If the FURUNO heading sensor PG-1000 is used, the data sentence “RMC” is necessary. The plot symbol changes over time as below. A vector appears about one minute after acquisition, indicating the target’s motion trend. Target Number 1. Press the MENU key. 2. Press the ARP SETUP soft key. 3. Select TARGET ID NUMBER. 4. Press the EDIT soft key. 5. A vector is a line extending from a tracked target which shows estimated speed and course of the target. The vector tip shows an estimated position of the target after the selected vector time elapses. You can evaluate a target’s actions by the spacing between dots.

Your unit can automatically advance to the next waypoint on a route, so you do not have to change the destination waypoint repeatedly. A route name may consist of six characters; comment, 13 characters. 6. Press the LOCAL LIST or ALPHA LIST soft key to open the waypoint list. 7. Save route window DISTANCE INTERVAL 00.1nm (When selecting BCKTRK DIST.) 3. PLOTTER OPERATION SAVE ROUTE. Press the START LOG and RETURN soft keys followed by the MENU key to close the menu. At this moment, a voyage-based route will be created. 8. Note: The maximum number of waypoints in a route is 35. If this number is exceeded an error message appears. The route is redrawn, eliminating the waypoint removed. 9. Press the MENU key to close the menu. 3.9.5 Erasing routes 1. For either of the above methods, a solid light-blue line with arrows runs between waypoint selected and own ship’s position. Arrows on the line show the direction to follow to get to the waypoint. Make a route using the soft keys, then push the ENTER knob. The cursor is on the waypoint nearest own ship. Also, if you don’t need to return to the original course, you can go directly to the next waypoint, as in Line 2 in the figure below. The area that defines an arrival zone is that of a circle which you approach from the outside of the circle. The alarm will be released if your boat enters the circle. When the arrival alarm is active a red dashed circle marks the arrival alarm area. When the anchor watch is active, a red dashed circle with an “X” at its center marks the anchor watch area. Your ship's position where you start the anchor watch alarm. When the XTE alarm is active two red dashed lines mark the XTE alarm area. Own ship position Intended course 1. When own ship is within a waypoint’s proximity alarm radius, the alarm sounds. The proximity mark remains on the screen until the waypoint is erased. The area searched is user-definable and is identified by a red triangle on the screen.

Additionally it displays the time of sunrise and sunset, moon shape (on current data.) 1. Use the Trackball to place the cursor on a current icon ( 2. For example, the following window appears for a lighthouse. Color white Height 7. 00 Meters Light characteristic occulting XXXXXXXX XXXXXXXX Sample lighthouse data 5. If necessary, move the Trackball downward or upward to scroll the window. 6. Press the CANCEL soft key twice to finish. Tide information The C-MAP NT chart card provides for calculation of the tide heights for any date. CHANGE DATE (DAY. MONTH. YEAR) 10. 1998 LIMIT: 31.12.2099 Date window 6. Use the Trackball to position the cursor where desired, then enter date with the alphanumeric keys. Repeat to enter complete date. 7. This section shows you what you can do with track, from turning it on or off to changing its plotting interval. In the default setting, own ship’s track is turned on and is displayed in red. AIS ONLY (AIS equipped): Show only AIS tracks. BOTH: Show both ARP and AIS tracks. 11. Target track Like own ship’s track, target tracks can be displayed in red, yellow, green, light-blue, purple, blue and white (default setting). You are asked if you are sure to change the track memory capacity. 6. Push the ENTER knob. 7. Press the MENU key to close the menu. 3.6.6 Erasing track This paragraph shows you how to erase own ship’s track and target tracks. LINES STYLE - - - - Lines style window 3. Use the Trackball to select line style desired, then press the ENTER soft key. The line style “dot”. The steps which follow show you how to change waypoint data. 6. A flashing diamond mark appears on the waypoint when it is correctly selected. LARGE: Shows mark in actual shape. SMALL: Displays all waypoints with an “X” regardless of mark shape selected. OFF: Turns off all waypoints and their names. Waypoints currently used in navigation are shown regardless of this setting. The sequence of waypoints leading to the ultimate destination is called a route.

You are asked if you are ready to download or upload waypoints and routes. 10. To prevent trouble, do not output the same data from multiple sources. 1. Press the MENU key to open the menu. 2. Press the SYSTEM CONFIGURATION, SYSTEM SETUP, PORT SETUP and OUTPUT THROUGH NETWORK soft keys. For mode-specific menus, e.g. radar, plotter and sounder, make sure that you select the appropriate display when making changes or viewing menu options. General Setup This paragraph shows you how to set up functions common to the plotter, radar and sounder displays. Language Chooses menu language. Range Unit Chooses unit of range and speed measurement. Temperature Chooses unit of water temperature Unit measurement. Depth Unit Chooses unit of depth measurement. Wind Unit Chooses unit of wind measurement. Speed Chooses speed format to display. Position Chooses how to display position. Display Examples of MGRS indications: 18S: Locating a point within the Grid Zone Designation 18SUU: Locating a point within a 100,000-meter square. Mode Bearing Chooses bearing display format for Readout course, course over ground and cursor bearing. Magnetic The magnetic variations for all areas of Variation. Relative with no heading input. True only in course-up, north-up and true motion. Cursor Chooses how to display cursor position.Effective when HUE soft key is set for MANUAL SET. Echo Color Chooses echo color. 2ND Echo Reduces second-trace echoes. After choosing the ranges desired, change the range with the RANGE key to activate range settings. Available ranges depends on the radar used. At least two ranges must be turned on. The default radar function key settings are as shown in the table below. Function Key If the above settings are not to your liking you may change them as follows: 1. HL: HDG LINE OFF Turns heading line off. MOD: MODE Selects presentation mode. GAI: GAIN Shows gain sensitivity adjustment window. Displays FTC window.

The default plotter function key settings are as shown in the table below. Add new waypoint. Menu Item Function Assigns no function. ADD: ADD NEW WPT Registers waypoint at cursor position. For example, the position of the ship is shown to be at sea while it is in fact moored at a pier. Land Features Turn land features on or off. CONTOUR LINE Soft key Spot Soundings Turn water depth display on or off. Safe Contour Paint areas in dark blue (default Shading. When the function is turned on, DECLUT.Setting SHOW FROM Data Boxes Setup You may select the data to show in the data boxes for the plotter, radar and sounder displays. For GPS receiver other than a FURUNO BB GPS, speed averaging and local time offset (to use local time) are also available. Press the MENU key followed by the SYSTEM CONFIGURATION, NAV OPTION and NAV SOURCE SETTINGS soft keys to display this menu. Enter Calibration amount in percentage. Wind(MWV) Chooses source of wind data. Select Source FURUNO BB GPS to get wind data from WS-200. Chooses source of air temperature data. Temperature Select FURUNO BB GPS to get air Source temperature data from WS-200. Press the MENU key followed by the SYSTEM CONFIGURATION, NAV OPTION and GPS SENSOR SETTINGS soft keys to display this menu. This change can be reduced by smoothing the raw GPS fixes. GPS STATUS Displays GPS satellite status display. (soft key) Requires FURUNO BB GPS receiver or GPS navigator outputting the data sentence GSA or GSV. For further details see the chapter on Maintenance. 7-26 Settings Max. Item WAAS MODE Select ON to use the WAAS mode. WAAS SEARCH WAAS satellite can be searched automatically or manually. For manual search, enter appropriate WAAS satellite number. WAAS ALARM When the WAAS signal is lost, the audible alarm sounds with the visual message “NO. The following display appears. DISPLAY DATA POSITION WPT POSITION BEARING RANGE DEPTH TEMPERATURE LOG TRIP TIME TO GO DATE TIME WIND Nav data setup window 5.

Press the CLEAR key to silence the alarm. You can see which alarm has been violated on the ALARM menu. In the example below the arrival alarm has been violated. 1. Plotter alarm messages and their meanings.You can reset the trip distance to zero as follows: 1. Press the MENU key. 2. Press the SYSTEM CONFIGURATION and GENERAL SETUP soft keys in that order to show the GENERAL SETUP menu. Sounder Displays 4.1.1 Selecting a sounder display There are seven display modes from which to choose: dual frequency, single frequency, marker zoom, bottom zoom, bottom lock, bottom discrimination, and A-scope. It can be turned on or off with TEMPERATURE GRAPH on the SOUNDER MENU. Therefore, the high frequency is ideal for detailed observation of fish school. Sounding area and transmission frequency Marker-zoom display The marker-zoom display expands a selected area of the normal sounder picture to full vertical size of the screen on the left-half window. A bottom displayed with a short echo tail usually means it is a soft, sandy bottom. A bottom displayed with a short echo tail usually means it is a soft, sandy bottom. A long echo tail means a hard bottom.How to use the SPLIT soft key (example: dual frequency display) Automatic Sounder Operation Automatic sounder operation is useful when you are preoccupied with other tasks and do not have the time to adjust the display. Use a higher gain setting for greater depths and a lower setting for shallow waters. Gain too high Examples of proper and improper gain Press the GAIN key to show the gain window, and adjust the ENTER knob or Trackball. You may also use the Trackball to shift the VRM. 2. The higher the number the higher the degree of suppression. Note that the clutter suppressor may erase weak echoes. Therefore, turn off the clutter when its use is not required. For example, you may want to display the bottom echo in white to discriminate fish echoes near the bottom. 1. Press the MENU key. 2.

The fractions in the window denote the number of scan lines produced per transmission. STOP freezes the display and it is convenient for observing an echo. You may set up the sounder alarms on the SOUNDER ALARM menu, which may be displayed by pressing the ALARM key. To activate the bottom alarm, the depth must be displayed. Note that the bottom alarm is turned on or off reciprocally with the bottom alarm on the plotter alarm menu. When an alarm setting has been violated the buzzer sounds and the speaker icon appears in red. Press the CLEAR key to silence the alarm. At this time the color of the speaker icon changes from red to background color. The size of the fish school can be ascertained from the density of the display. RANGE: Choose to use the AIS function within the range you specify. Use the numeric keys to enter the range from own ship and then go to step 8. Symbol Activated automatically or manually. The dashed line shows ship’s SOG and COG (or STW and CTW). The solid shows target bearing. Activated target A target whose CPA and TCPA are within the CPA and TCPA values set by the operator. When this occurs, the target is marked with the (flashing) lost target symbol. However, the target which becomes a lost target is a activated target or a sleeping target within the lost target range. You can evaluate a target’s actions by the spacing between dots. Below are examples of dot spacing and target movement. (a) Ship turning (b) Ship running To turn the AIS past position display on or off:. Memory Card Operations The memory cards store these data: marks, lines, waypoints, routes, track, position, water temperature and setting data (plotter only). This feature is useful for observing past data and setting up the equipment for a specific purpose with “setting data.” 1. Note that radar and sounder data cannot be uploaded or downloaded. 6.2.1 Setting communication software on the PC The communication format (RS-232C) with the PC is as follows: Baud Rate:.

TVG (Time Varied Gain) compensates (HF,LF) for propagation attenuation of the ultrasonic waves. The only) setting range is 0-10; the higher the setting the greater the extent of suppression. All default basic ranges are restored whenever the unit of depth measurement is changed. The default sounder function key settings are as shown in the table below. Function Key If the above settings are not to your liking you may change them as follows: 1. MOD: AUTO MODE Display automatic mode selection window. SFT: SHIFT Shifts range in manual operation. You may choose which to display and setup the depth and temperature graphs as follows: 1. Hazardous voltage which can cause electrical shock exists inside the equipment. Only qualified personnel should work inside the equipment. When you suspect that the synchro belt has worn out, contact a FURUNO agent or dealer about replacement. (Type: 40 S2M 266UG, Code No.: 000-808-743) Trackball Maintenance If the cursor skips or moves abnormally, you may need to clean the Trackball. If you cannot restore normal operation do not attempt to check inside the unit. Any trouble should be referred to a qualified technician. The equipment displays GPS receiver program version number, and checks the GPS unit for proper operation, displaying OK or NG (No Good) as the result. The equipment displays network sounder program version number, checks the ROM and RAM, and displays water temperature (appropriate sensor required) and depth. It is available with connection of a FURUNO BB GPS receiver or a GPS receiver outputting the data sentence GSA or GSV. 1. Press the MENU key. Note: The message “SYSTEM HAS FAILED START UP TEST.It is not an indication of malfunction. No bearing pulse from radar antenna. No position data is present. Possible problem with FURUNO BB GPS receiver.Points to North. Correct chart and suitable scale - full chart reliability. Chart overenlarged. Plotter, radar, sounder alarm setting violated.

Track is not being recorded or plotted. Chart offset applied. Voyage-based route currently being created. Latitude and longitude position offset applied. Voltage of battery on circuit board in display unit is low. SD card - FURUNO or NAVIONICS chart card available C-MAP chart card also available Arrival and Anchor watch, Cross track error and proximity alarms, Ship’s speed in and out alarms, Water temperature. FURUNO's network fish finders implement the same tried and true fish finding technology that is used in our commercial-grade fish finders. Plug a network fish finder into your NavNet vx2 system and it turns any display in the network into a high-performance fish finder. This transceiver gives you the flexibility to choose your operating frequencies for more productive fishing. Output power can also be selected among 1, 2, and 3 kW to suit a variety of situations. It shows your exact position and offers a variety of display modes that allow you to organize your nav data with unparalleled ease. It has even been voted Best Integrated Navigation System by the National Marine Electronics Association for three consecutive years. Now, NavNet vx2 is ready to carry on the tradition. Its wide range of options fulfils virtually every desire you may have for navigation system. Radar, GPS, Network fish finder, Network weather facsimile - a multistation integrated navigation network, NavNet vx2 lets you build your navigation system according to your needs. Utilizing state-of-the-art network technology, NavNet vx2 provides you with seamless data sharing and vast future expandability. The heart of NavNet vx2 is its Ethernet-based network. Up to four displays, together with various navigational sensors, can be interconnected in addition to new MaxSea-NavNet navigational software, which adds even more features to your NavNet vx2 network.

Stress-free navigation can be performed from any display unit connected to the onboard network, due to the high-speed transfer of data available. Radiation Hazard Only qualified personnel The radar antenna emits electromagnetic should work inside the radio frequency (RF) energy which can be equipment.Never look directly into the antenna aperture from Do not disassemble or modify the a close distance while the radar is in equipment.For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excelleEach NavNet product is assigned an IP address to enable transfer of images between other NavNet products. For example, video plotter pictures can be transferred to a radar and vice versa. Pictures received via the NavNet may be adjusted at the receiving end. The number of display units which may be installed depenTen keys are labeled and they provide the function shown on their labels. The five soft keys provide various functions according to current operating moTheir labels for their current functions are shown on the screen to the left of the keys. Each press of the key shows preset soft keys, user function keys or turns off navigation information (at the top of the screen). SOFT KEYS Display unit Some soft keys show the current setting of a soft key in reverse video as shown below. Insert the appropriate chart card for your area as follows: 1. Open the chart drive. Chart slot Display unit 2. Insert chart card label side up. 3. Close the lid. To remove chart card, push the card once and then pull it out. Note 1: Do not remove a card while the chart is During this period the equipment is inoperative. The startup test checks the ROM, RAM, internal battery and backup data for proper operation, displaying the results for each as OK or NG (No Good). If NG appears an appropriat. Call us for details. We Ship Worldwide New COVID-19 Screening and Control Electronics Size: 10.

4 inches Type: Color LCD Size: 24 inches Type: Radome Output: 4 kW There is flexibilityCompatible with MaxSea-NavNet navigational software,Size: 10.4 inches Type: Color LCD Size: 24 inches Type: Radome Output: 4 kW There is flexibility. NavNet VX2 gives you seamless data sharing and nice future expandability. Easy navigation and operation can be performed from any display unit connected to the onboard network. Some of the early models were setup for using Navionics Gold XL3 microSD charts. Longer range scales of up to 72 nm. High power output for enhanced long range performance. Stylish, compact, lightweight with simplified installation and modest power consumption. To be clear, this is for the items shown in the first photo. The photos of chartplotter screen, radar, GPS, display etc.Do not assume any additional items will be included in your shipment.There are times a display is used ONLY to show the item being sold is functional and working properly. In this case these displays ARE NOT included, this will be stated in our descriptions. If you have ANY questions feel free to send a message or call Max Marine Electronics Inc, Pompano Beach, Florida. We always want to be transparent with our customers and fully disclose any information regarding the products we sell. A solution-minded staff, well versed in product functionality, compatibility and repair, is key to your satisfaction. Page Count: 10 It has e ven been voted Best Integ rated Na vigation System by the National Marine Electronics Association for three consecutiv e y ears. Now, NavNet vx2 is ready to carr y on the tradition. Its wide range of options fulfils vir tually e very desire you ma y hav e for y our navigation system.F rom a stand-alone, single station navigation system to a multistation integr ated navigation network, Na vNet vx2 lets you build y our navigation system according to y our needs.

Utilizing state-of-the-ar t network technology, NavNet vx2 pro vides you with seamless data sharing and vast future e xpandability. The hear t of NavNet vx2 is its Ethernet-based network that allows multiple displa ys to be connected. Interconnect the displa ys with various navigational sensors and our ne w MaxSea-NavNet na vigational software f or a feature rich network that is unparalleled. Stress-free navigation and oper ation of any component can be perf or med from any displa y unit connected to the onboard network. 1 NavNet vx2 2 NavNet vx2 Once you ha v e selected the display units f or your system, you can now choose the basic operating equipment of the Na vNet vx2 system. Y ou can create your own network by selecting components according to y our needs. With a variety of optional add-ons, Na vNet vx2 can offer you additional useful functions, such as: radar ov er lay, AIS displa y, NA Vpilot autopilot data and ARP A target trac king. Y ou can e ven interf ace it with your PC and MaxSea-NavNet PC software to mak e it the most versatile na vigation networ k on the market.P owerful X-Band transmitters off ers detailed target detection. While the compact 2.2 kW and 4 kW radomes off er the maximum range of 24 and 36 nm respectively. High performance open arrays off er longer detection ranges. Radar overlay Radar targets can be ov erlaid onto the electronic char t so that you can better recognize what's around y our vessel b y referencing the target locations on both the char t and the radar. Echo trails This f eature displays afterglo w of all the targets to show their trac ks. It helps you f oresee their heading directions at a glance. Its trail duration is adjustable among 15, 30 s, 1, 3, 6, 15, 30 min and continuous.FURUNO's netw ork fish finders implement the same tr ied and true fish finding technology that is used in our commercial-grade fish finders.